We already have a general post on what not to click when Unraid says unmountable. This one is narrower: a disk that goes unmountable right after an OS update and reboot, when nothing else changed and SMART is clean. That timing usually points to missing metadata, not a failing drive, and missing metadata is usually fixable if nothing writes over the disk first.
What owners have actually reported
We went looking for public reports before writing this. Here is what we found, and only what the sources say:
- Unraid 7.2.3 → 7.2.4, March 2026. In a bug report on the Unraid forums, one device in a four-NVMe Btrfs RAID1 cache pool came back from the upgrade reboot with its GPT partition table zeroed and all three Btrfs superblock copies (at 64 KiB, 64 MiB, and 256 GiB) zeroed. The poster reported the drive itself was healthy and the data regions were intact. Because the pool was RAID1, nothing was lost. The poster thought a device mix-up at boot made Unraid treat the drive as a new, blank disk. That is their theory, not a confirmed cause. The moderator who replied said it was not a general problem and was most likely the reboot rather than the upgrade.
- Unraid 7.0.1 → 7.2.3, December 2025. A single cache drive showed unmountable after the upgrade. The drive had no partition at all. The moderator again said it was "certainly not the update; it could have been the reboot." He had the owner recreate the partition at sector 2048 with sfdisk and keep the existing signature, then re-import the pool. The data came back.
- Unraid 7.0.3 → 7.3.1, May 2026. The server didn't come back after the update reboot. The CMOS battery was dead, so the BIOS had reset. After fixing the boot order, Unraid said Disk 1 was "too small" for its slot, then unmountable, and xfs_repair found no superblock. The owner synced parity anyway. The cause turned out to be a Host Protected Area (HPA): the drive was reporting slightly fewer sectors than it really has, so the partition didn't line up. Once the HPA was removed and the partition recreated, Disk 1 mounted with its data.
- Unraid 7.1.4, October 2025. Two array disks went unmountable after the update. One came back once the partition was recreated. For the other, xfs_repair found a secondary superblock, rewrote the primary, and the disk mounted.
The one official item is in the Unraid 7.2.5 release notes (April 30, 2026). When an array disk with a non-standard partition layout, such as an old sector-63 alignment, was unassigned and reassigned, Unraid rewrote the partition at sector 64, which made the existing filesystem unmountable. 7.2.5 now keeps the existing layout. If you are on an older 7.2.x and reshuffling disks, that matters.
Two honest caveats. First, none of this is a single, widespread "update wipes disks" bug. The moderators handling these threads mostly blame the reboot, the BIOS, or the hardware, not the update itself. Second, the update reboot is often the first full cold start in months, so problems that were already waiting tend to show up then. Either way, the disk in front of you looks the same: present, healthy, and unmountable.
Why "no file system" doesn't mean "no files"
An XFS or Btrfs disk in Unraid has a partition table at the front, then a filesystem whose superblock says how everything else is laid out. Your files are spread across the rest of the disk. If the partition table is gone, points to the wrong start sector, or the disk suddenly reports a smaller size, Unraid can't find the superblock and calls the disk unmountable. The same is true if the superblocks themselves were zeroed. In every case above, the files sat untouched behind the missing metadata.
That is also why "xfs_repair can't find a superblock" isn't the end. If the partition is misplaced, the tool is searching the wrong place. Fix where the partition starts, and the superblock is often right where it should be.
If Unraid went unmountable right after an update and the disk is healthy, the fix is usually small. The mistakes that make it permanent are Format, a rebuild onto the original disk, and New Config guesses.
What not to do
- Don't check Format. Unraid's own documentation says: "Never format an unmountable disk through the WebGUI! Formatting erases all data and updates parity, making recovery impossible."
- Don't rebuild onto the original disk unless the emulated disk mounts and shows your files. If the emulated disk is unmountable too, a rebuild writes that onto your only copy.
- Don't run a correcting parity check or a parity sync to "fix" it. It doesn't repair the unmountable disk, and it throws away the parity you might have needed to emulate it.
- Don't keep starting the array with autostart on. Turn off array autostart (Settings → Disk Settings) so the next reboot doesn't start anything on its own while you investigate.
- Don't New Config and shuffle slots until you know which serial number belongs in which slot. A disk in the wrong slot with "parity is already valid" checked is how one unmountable disk becomes three.
- Don't run xfs_repair -L, or btrfs check --repair, as a first move. Both write. If the real problem is the partition or the disk size, they are repairing the wrong thing.
What to do instead
- Stop the array and turn off autostart. If a disk is clicking or SMART errors are climbing, power the server down. That is a different problem.
- Download diagnostics (Tools → Diagnostics) before rebooting again. The bug report above lost its key evidence because the syslog rotated before anyone looked.
- Collect read-only information. In the forum threads, the moderators asked for
fdisk -l /dev/sdX,blkid, and, for a disk that reports the wrong size,hdparm -N /dev/sdX. These only read. Note the serial number behind each sdX, because sdX names can change between boots. - Check whether the disk size changed. If Unraid says the disk is too small, or the BIOS was just reset, look for an HPA before you touch anything else.
- Ask before writing. The Unraid forums are good at this, and every fix above came from a moderator reading diagnostics. The fixes themselves (sgdisk, sfdisk, hdparm -N p…, a pool re-import) are writes. They're small and targeted, but they are writes.
- If the data matters and isn't backed up elsewhere, image the disk first. A full sector copy means a wrong guess costs you a copy, not your data. If you don't have a spare disk that big or a way to make a clean image, that is where a lab comes in.
When it's a lab case
Most of these never need us. A partition recreated in the right place, or an HPA removed, and the disk mounts. It becomes lab work when the disk is also failing, when xfs_repair or btrfs repair already ran and made changes, when someone formatted or rebuilt over it, or when there's no backup and you don't want the first write to be on the original.
What we do is the same as for any NAS or array case: we image every disk first, sector by sector, and work only from the copies. We find where the partition and filesystem actually start, rebuild the metadata on the image, and copy the files out. We don't start your array or run repair tools on your originals. We don't publish a success rate, and we won't promise anything before an evaluation. A completed format or a rebuild that overwrote the disk is a different situation from missing metadata, and we will tell you which one you have.
Desert Data Recovery is a Phoenix-area lab, founded in 2013 and now a division of ioLogik LLC. Arizona drop-off is on the locations page. Everywhere else is mail-in. If you're shipping disks, pack them like this and label each one with its Unraid slot. Call (602) 686-2622, Mon–Fri 9:00am–5:00pm.
Unraid unmountable after update FAQ
Is there a known Unraid bug that wipes disks during an update?
xfs_repair says it cannot find a secondary superblock. Is the data gone?
Will rebuilding the disk from parity fix it?
A forum moderator gave me an sgdisk or sfdisk command. Should I run it?
I already formatted it, or ran a parity sync. Is it too late?
An Unraid disk that went unmountable after an update usually still has its files. Don't format, don't rebuild over it, and get diagnostics before you write anything. If it's also failing or has no backup, start with a free evaluation.
Request free evaluation →Free evaluation · No data, no fee · Talk directly with a technician.